GCPZY-100塑料高分子材料膨脹系數測試儀（GCPZY-100 plastic polymer material expansion coefficient testing apparatus）

該裝置用于測試橡膠,塑料等高分子材料在一定溫差下測量長度的變化值，由此可計算其一定溫度下的平均膨脹系數，參照國標：GB1036-2006測試方法。

The device is used for test of rubber, plastic and other polymer material measuring length changes in a certain temperature difference value, which can calculate the average expansion coefficient, the temperature of the reference standard test method for: GB1036-2006.

Main technical parameters:

1 zui高爐溫：室溫-100℃。

The 1 highest temperature: room temperature -100 ℃.

2 升溫速度，實驗過程控制參數，含PID參數。

2 the heating speed, the experimental process control parameters, including PID parameters.

⑴由智能儀表實現全過程任意調節、設置、鎖定。操作見儀表說明書。

⑴ by the inligent instrument to realize the whole process of arbitrary regulation, setting, lock. See the manual operation instrument.

⑵提供由上位機（計算機）接口，可實現在線檢測。

The provided by the host (computer) interface, can realize online detection.

3 電源電壓：220V±10﹪，50HZ

The 3 power supply voltage: 220V ± 10, 50HZ

4 恒溫水槽zui高溫度可達100度，加熱zui大功耗≤2KW

4 constant temperature water tank temperature can reach 100 degrees, the heating power ≤ 2KW

5 膨脹值測量范圍與誤差：0--5㎜±0.1%

The 5 expansion value measurement range and error: ± 0.1% 0--5 mm

6 控溫精度：±0.1℃ 溫度記錄值誤差≤±0.5﹪

Temperature control accuracy: 6 ± 0.1 ℃ temperature record value error less than ± 0.5

7 測量膨脹值分辨率：1um

7 measuring the expansion value resolution: 1um

8．測量容積1.8升，不銹鋼真空保溫?？裳b低溫液體進行低于環境溫度的線膨脹系數測試試驗。

8 measurement of the volume of 1.8 litres, stainless steel vacuum insulation. Can be installed in cryogenic liquid is lower than the environment temperature linear expansion coefficient test test.

9．測試容積溫度檢測：zui小分辨：0.1℃

The 9 test volume temperature detection: the minimum resolution: 0.1 ℃

10．測試架石英管，以及石英外管，石英活塞頂桿

The 10 test frame quartz tube, quartz tube, quartz rod, piston top

11．樣品大?。簔ui大50長*20寬*3—6厚（mm）

11 sample size: 50 maximum length *20 width *3 6 thickness (mm)

12．測試系統滿足標準：GB/T 20673-2006,GB 1036-89 塑料線膨脹系數測試定方法的技術要求和精度要求。

12 test system meet the standards: GB/T 20673-2006, GB 1036-89 plastic linear thermal expansion coefficient of the technical requirements of test method and the precision requirement.

13．采用石英標樣標定儀器系統

13 using quartz calibration instrument system standard sample

配置：測試主機一臺，低溫水槽一臺；測試軟件一套，計算機一臺。標樣一個。

Configuration: a test mainframe, cryogenic tank a; testing a set of software, a computer. Standard sample a.

更多產品請關注北京冠測試驗儀器有限公司

：

：吳 芳