AW氣動執行器主要特點AW Main features pneumatic actuators
  AW系列氣動執行器分為雙作用式和單作用式（彈簧復位），兩個氣體分缸，輸出扭矩大，動作靈活平衡；活塞桿鍍硬鉻，有很好的耐磨性；所有滑動部件之間配有無油潤滑軸和導向環以降低摩擦系數，延長使用壽命AW氣動執行器的U型曲線特性輸出扭矩更適用于大口徑球閥、蝶閥等轉角行程閥門的啟、閉和調節，也可用于其它回轉運動的場合，是實現工業管道自動化控制的理想裝置。

AW Series pneumatic actuators are divided into double-acting and single acting （spring return）, two sub-cylinder gas, the output torque, balanced and flexible movement; hard chromium plated piston rod, good wear resistance; all sliding between parts with or without oil lubrication shaft and guide ring to reduce friction and prolong the life of AW pneumatic actuator output torque characteristic U-shaped curve is more suitable for large-diameter ball valve, butterfly valve stroke corner Kai, closed and regulation, can also be used for other rotary movement of the occasion, is to achieve the ideal of industrial automation control device pipeline.

標準參數Standard parameters

型號編制Model preparation

型號選擇Model selection
    選用時，先確定閥門啟、閉的扭矩，再根本閥門使用的流體介質，增加安全值。對清潔、潤滑介質增加20%
安全值；對水蒸汽或非潤滑介質增加25%安全值；非潤滑的干氣介質增加60%安全值；非潤滑氣體輸送的顆粒粉料介質增加
100%安全值。然后根據氣源工作壓力，查找雙作用式或單作用式輸出扭矩表，可得到準確的執行器信號。單作用式輸出扭矩
表中，zui小彈簧扭矩即為關閉閥門時的扭矩，zui大彈簧扭矩即為打開閥門時的扭矩。

AW pneumatic actuator used, make sure the valve opens, closing torque, and then do the valve using a fluid medium, added security value. For cleaning, lubricating medium increased by 20%
Security value; of water vapor and non-lubricating medium security value by 25%; non-lubricated dry gas media to increase 60% security value; non-lubricated gas transmission medium to increase the powder particles
100% security value. Then the gas supply pressure of work, find the double-action or single-acting output torque table, available and accurate actuator signal. Single-acting torque
Table, the minimum time to close the valve spring torque is the torque, maximum torque is to open the valve spring torque.

氣動執行器附件的功能及用途Pneumatic actuator attachment functions and uses of
1、雙作用執行器：對閥門開啟和關閉的兩位式控制。
2、單作用執行器（彈簧復位）：在電路、氣路切斷或有故障時，自動關閉閥門。
3、單電控電磁閥：供電時閥門開啟或關閉，斷電時閥門關閉或打開（可提供防爆型）。
4、雙電控電磁閥：一個線圈通電時閥門開啟，另一個線圈通電閥門關閉，有記憶功能（可提供防爆型）。
5、限位開關回訊器：遠距離傳閥門開或關位置的信號（可提供防爆型）。
6、電氣定位器：根據電流信號（4~20MA）的大小對閥門的介質流量調節控制（可提供防爆型）。
7、氣動轉換器：將電流信號轉換成氣壓信號，與氣動定位器配套使用（可提供防爆型）。
8、氣動定位器：根據電流信號（標準0.02~0.1MPA）的大小對閥門的介質流量調節控制。
9、氣源處理三聯件：包括空氣減壓閥、過濾器、油霧器。對氣源穩定、清潔及運動部件起潤滑作用。

1, double-acting actuators: valve opening and closing of two control.
2, single-acting actuator （spring return）: In the circuit, gas cut off or fails, automatically close the valve.
3, single solenoid valve: open or close the supply valve, the valve closed or open, when power failure （explosion proof available）.
4, double solenoid valve: a valve open when the coil is energized, the other coil is energized, the valve closes, with memory function （available in explosion-proof）.
5, limit switch back to the hearing: long-distance transmission valve open or closed position signals （explosion proof available）.
6, electrical locator: According to the current signal （4 ~ 20MA） the size of the media flow control valve control （available in explosion-proof）.
7, pneumatic converter: the current signals into pressure signals, and supporting the use of pneumatic positioner （providing explosion proof）.
8, pneumatic positioner: According to the current signal （Standard 0.02 ~ 0.1MPA） the size of the media flow control valve control.
9, Air Treatment FRL: including air relief valve, filter, lubricator. Of the gas source stable, clean and lubricate moving parts.

手操機構：自動控制在不正常情況下可以手動操作閥門的啟閉。

HART institutions: automatic control under normal circumstances you can not manually open and close the valve.

外形尺寸雙作用式Dimension Double-action

單作用式外形尺寸Single-acting Dimensions

雙作用式輸出扭矩（N、M）Double-acting torque

單作用式輸出扭矩（N、M）Single-acting torque

氣缸容積及重量和耗氣量計算Cylinder volume and weight and calculation of air consumption

注： 雙作用式計算公式V+（A+B）︱（P+101.2）÷98︱M
       單作用式計算公式V=A︱（P+101.2）÷98︱M
V：  耗氣量NL/min（N升/分）
P：  氣源壓力KpaG（表壓）
M：  活塞每分鐘往復次數
A.B：氣缸容量（見表）
將Mpa轉換成Kpa乘以1000

Note: Double-action formula V + （A + B） ︱ （P +101.2） ÷ 98 ︱ M
Single-acting formula V = A ︱ （P +101.2） ÷ 98 ︱ M
V: Air Consumption NL / min （N L / min）
P: Air pressure KpaG （gauge）
M: number of reciprocating piston per minute
A.B: cylinder capacity （see table）
Will Mpa multiplied by 1000 to convert Kpa

安裝使用與維護Installation and maintenance
1、氣動執行器可與閥門直接連接，也可通過支架和接頭與閥門安裝連接。連接緊固件不得松動。
2、保證執行器輸出軸與閥桿安裝的同軸度，并轉動靈活，無爬行現象。
3、連接管道、接頭、附件等應清潔干凈。
4、電磁閥排期口始終向下，當向上或水平時，應連接彎管，使排氣口向下。
5、調試前應確定空氣管道通暢，氣壓、電壓、信號等符合要求。
6、壓縮空氣應經過過濾、干燥、露點-15℃以下要除濕。
7、調試時電磁閥應開到自動位置。
8、氣動操作時，應斷開手動裝置，手動操作時應斷開氣動裝置。
9、執行器上安裝的各種附件，應分別參照使用說明進行調試、
10、正常工作情況下每月檢查一次，每年檢修一次。

1, the pneumatic actuator can be directly connected with the valve, brackets and fittings can also be connected with the valve installation. Fasteners must not loose connection.
2, to ensure that the actuator output shaft coaxial with the valve stem is installed, and turn the flexible non-crawling phenomenon.
3, connecting pipes, fittings, accessories, etc. should be clean.
4, solenoid valve scheduled port is always down, when the level up or when the pipe should be connected so that the exhaust downward.
5, testing should be determined before the channel clear air, pressure, voltage, signals meet the requirements.
6, compressed air should be filtered, dried, dew point -15 ℃ to dehumidify the following.
7, solenoid valve should open when debugging to the automatic position.
8, pneumatic operation, the device should be disconnected manually, manually operated pneumatic devices should be disconnected.
9, the actuator is installed on a variety of accessories, should be separay described with reference to use for debugging,
10, under normal operating conditions once a month, once a year overhaul.