122-01POLYIMIDE COATING聚酰亞胺涂層

說明：122-01是單組分、電絕緣、耐溶劑、聚酰亞胺基、粘合劑

以及適于通過絲網印刷、浸漬和注射器分配應用的涂層。這個產品是為

裝配電氣和電子部件。固化計劃允許快速處理和

粘合劑在高溫下具有優異的熱穩定性和附著力。122-01是CMI的未填充版本

110-19。

典型固化特性：

稠度光滑膏

玻璃變壓器。臨時雇員。（攝氏度）>250

水解穩定性優異

有效溫度范圍（℃）-55至+230

熱穩定性（攝氏度）達到325

T-抗剪強度（psi）>1500

建議的處理和固化：122-01已準備好可供使用。在表面涂上粘合劑

用手工和/或自動方法粘合和裝配。施加輕微壓力以確保表面良好配合

以及菲力的形成。在200℃下固化1小時后，大多數應用的性能。良好性能

通過在150°C至210°C的溫度下固化，在多種基底上獲得。小

固化時間和溫度，以確保180°C下的耐溶劑性為1小時。建議終用戶

通過實驗確定適合個人應用的溫度和時間。

儲存：保質期：23°C或更低溫度下儲存1年。在更高的溫度下儲存可以提高樹脂的性能。

**請注意：122-01在儲存過程中可能結晶。要重新熔化晶體，請將其放在溫水浴中或熱的

在90°C–100°C下加熱，直到晶體溶解。不要無人看管。融化晶體的時間是

取決于質量。

安全和操作：在通風良好的情況下使用。遠離火花和明火。避免長時間

接觸皮膚和吸入蒸汽。用肥皂和水清洗皮膚。

122-01POLYIMIDE COATING聚酰亞胺涂層

122-01
POLYIMIDE ADHESIVE / COATING
DESCRIPTION: 122-01 is a single component, electrically insulating, solvent resistant, polyimide based, adhesive
and coating suitable for application by screen-printing, dipping and syringe dispensing. This product is designed for
assembling electrical and electronic components. The cure schedule allows for rapid processing and the resulting
bond exhibits excellent thermal stability and adhesion at high temperatures. 122-01 is an unfilled version of CMI
110-19.
TYPICAL CURED PROPERTIES:

Consistency Smooth Paste
 Glass Trans. Temp. (°C) > 250
 Hydrolytic Stability Excellent
 Useful Temperature Range (°C) -55 to +230
 Thermal Stability (°C) Good to 325
 T-Shear Strength (psi) >1500
SUGGESTED HANDLING & CURING: 122-01 is ready to use as supplied. Apply adhesive to surface to be
bonded by hand and/or automatic method and assemble. Apply slight pressure to assure good mating of surfaces
and formation of filet. Best properties for most applications result when cured for 1 hour at 200°C. Good properties
are obtained on a variety of substrates by curing at temperatures ranging from 150°C to 210°C. The minimum
cure time and temperature to assure solvent resistance is one hour at 180°C. End user is advised to
experimentally determine temperature and time best suited for individual applications.
STORAGE: Shelf Life: 1 year when stored at 23°C or less. Storing at higher temperatures may advance the resin.
** Please note: 122-01 may crystallize during storage. To re-melt crystals, place in a warm water bath or on a hot
plate at 90°C – 100°C. Heat only until crystals dissolve. Do not leave unattended. Time to melt the crystals will be
dependent upon the mass.
SAFETY & HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid prolonged
contact with skin and breathing of vapors. Wash with soap and water to remove from skin.