黄色视频不卡_午夜福利免费观看在线_亚洲国产精品999在线_欧美绝顶高潮抽搐喷水_久久精品成人免费网站_晚上一个人看的免费电影_国产又色又爽无遮挡免费看_成人国产av品久久久

瑞士KALLER氮?dú)飧?瑞士KALLER氮?dú)鈴椈?/strong>

X2400-075
X2400-063
X1000-050
X1000-013
X1000-032
X1000-063
X1000-38
X1000-025

瑞士KALLER氮?dú)飧?瑞士KALLER氮?dú)鈴椈?/strong>

使用注意事項：氮?dú)鈴椈蔀楦邏好芊庵破?，出廠前經過嚴格的檢查和測試，不允許有任何的氣體泄漏現象，因此要求用戶正確
地安裝和使用，才能確保其安全可靠性和*的使用壽命。
1 .當?shù)獨鈴椈勺鳛楠?dú)立部件使用時，安裝到模具后，在使用壽命范圍內一般無需拆卸維修。
2 .若將氮?dú)鈴椈蛇B成系統使用，一般需由經過專門訓練的人員或?qū)I(yè)人員的指導，應特別注意在氣缸中的氮?dú)馍形?釋放前，
嚴禁 拆卸或進行維修，以防意外事故發生。
3 .氮?dú)鈴椈上露说穆葆斨饕鸨Ｗo(hù)和加強密封作用，不得擅自拆卸和隨意敲擊。
4 .推薦工作行程≤0 . 9 X S（制造行程），嚴禁超行程壓縮。
5 .被活塞桿上端頂壓的工件之接觸面與活塞桿軸線的不垂直度應≤1°（即應保持垂直，嚴禁偏載）。
6 .不可有側作用力，壓縮作用力必須以缸體底部垂直。
7 .氮?dú)鈴椈稍诒粔嚎s后，不要使活塞桿自由空回程，以免引起氮?dú)鈴椈蓛?nèi)部損壞。
8 .注意保持活塞桿圓柱表面的清潔，避免刮傷或刻痕，嚴禁敲擊碰撞。
9 .嚴禁將氮?dú)鈴椈芍糜诹胰障卤窈透邿嵩喘h(huán)境中，zui高允許溫度8 0°C（特制耐高溫氮?dú)鈴椈衫猓?。
1 0 .氮?dú)鈴椈蓱?yīng)存放在干燥通風、無腐蝕性氣體環境中包裝存放； 拆箱安裝后如長期不使用時可 在為其表面涂抹油脂保護防腐。
11.不得在氮?dú)鈴椈筛左w、密封圈等處做任何修改或加工。
1 2 .不得為減小行程而將活塞桿截短。
1 3 .不得對氮?dú)鈴椈杉捌涓郊M(jìn)行其它加工。
1 4 .不得以非氮?dú)鈿怏w充填氮?dú)鈴椈伞?br />1 5 .嚴禁非專業人員對氮?dú)鈴椈蛇M(jìn)行拆解和改造，否則將導致安全問題。
1 6 .將氮?dú)鈴椈傻撞抗潭ㄔ谄秸墓潭ò迳希褂眠^程中，氮?dú)鈴椈刹辉试S有搖動或竄動現象。
1 7 .氮?dú)鈴椈蛇\(yùn)輸時應使用包裝物進行包裝，不得相互碰撞。
1 8 .報廢時請將廢氮?dú)鈴椈筛綦x存放，不能與其它產品混裝，更不能以重物壓在廢缸體上。
1 9 .處理時請將氮?dú)鈴椈蓛?nèi)的氣體全部放出后再進行其它處理。
TOAN” Nitrogen Gas Spring contains high pressure nitrogen gas, each of TOAN gas springs is strictly inspected and tested;
any of leaking gas or damages are not allowed. Therefore we ask our customers install and use MASON correctly to ensure their safety
and TOAN’s reliable and suitable lifetime.
1.When gas spring is self-contained, normally there is no need to dismount after being installed in die.
2.At linked mode, only specially trained personnel with good knowledge about products should carry out the maintenance. To
avoid any of accidents, DO NOT attempt maintenance spring until internal pressure is exhausted.
3.Port plug is for the purpose of protection and seal. Do not release and strike.
4.The recommended stroke is less than 90% x stroke.
5.It is necessary to have a flat surf a c e a g a i n s t t h e b a s e of the spring in all circumstances. Contact misalignment should be
minimized ＜ 1°
6.The gas spring should not be subject to side loads. Never allow open clearances in a bottom mount or horizontal application.
7.Do not use the gas spring in such a way that the piston rod is released freely from its compressed position as this could cause
internal damage to the gas spring.
8.Keep piston rod clean. Avoid any of scratch and injury. Protect the piston rod against mechanical damage and contact with fluids.
9.The maximum operating temperature 80℃ (Except special high temperature resistance gas spring) Do not expose gas spring
under sunshine and high heat.
10.Store gas spring under dry and ventilation
11.Do not machine or modify.
12.Do not machine piston rod to fit the stroke.
13.Do not machine cylinder and its parts.
14.Do not charge any of gas except nitrogen.
15.Only trained and skilled technicians could mount and connect gas springs; otherwise there will be a safety concern.
16.Use the recommended mount solutions and dispose properly.
17.Pack properly and keep away from bumping while delivering.
18.While disposing, store gas springs separay. Do not mix with other products and put under any of heavy material.
19.Discharge gas compley before discard or any of disposing.